SS 904L tubing spools manufacturer in India
Manufacturer of prefabricated stainless steel spool from sizes ranging from 1” dia up to 18” dia pipes with full-penetration 1G girth welds
Stainless steel pipe spools specification
Dimensions
- 3 meter – 8” – 14”NB (DN200 – DN350)
- 6 meter – ½” – 6”NB (DN15 -DN150)
SS metal spool flange standard
- ASME B16.5 (Class 150 to 2500)
- ANSI / DIN / AWWA / JIS / API / PN standard
Wall thickness
- 3mm to 70mm
- Schedule 10S - XXS
SS 904L tubing spools heat treatment
- PWHT
- Preheating
Stainless steel flanged pipe spool welder test
- AWS ATF
- ISO 17025
Fabrication process
- Dimensioning
- Bending
- Cutting
- Welding
Welding standard
- ASME section IX
- Fabrication Tolarance – PFI ES3
- Bending PFI ES24
- Welders as per API1104 (Downhill / Uphill)
Fabrication parts
- 45° / 90°elbow (LR, SR)
- Tee / Reducing tee
- Cross / Reducing cross
- Weldneck / Blind / Slip on flanges
Key steps for SS pipe spool design
- Stress Analysis
- Isometric drawings
- 3D Modeling
- Support and Pipe Routing
Supplier of SS spool flange available in PED 97/23/EC, ASME B31.1, ASME B 31.4, ASME B31.3 and ASME B 31.8 standards
Successfully done SS pipe spool work in Malaysia, Maldives, Saudi Arabia and New Zealand
SS spool fabrication tolerances
| SS metal Bends | Shall not exceed 8% of nominal dia of the pipe |
| Stainless steel mitred joints | 3 deg or less |
| SS flanges | From square position : 2.5mm/m or ±1/32" or ±0.8 mm |
| Stainless steel alloy pipe spools | A plain end, 100-150 mm, 4-6" |
Stainles steel metal pipeline spool equivalent properties
| SS Grades | W.Nr. | UNS | EN |
|---|---|---|---|
| 304 | 1.4301 | S30400 | X5CrNi18.10 |
| 304L | 1.4306 | S30403 | X2CrNi19.11 |
| 310S | 1.4845 | S31008 | X12CrNi25.21 |
| 321 | 1.4541 | S32100 | X6CrNiTi18.10 |
| 316 | 1.4401 | S31600 | X5CrNiMo17.12.2 |
| 316L | 1.4404 | S31603 | X2CrNiMo17.12.2 |
| AISI 904L | 1.4539 | N08904 | X1NiCrMoCu25.20.5 |
Looking for stainless steel alloy fabricated spools in Schedule 10S to XXS at lowest cost? send us a message
SS alloy pipe spools
Stainless steel flanged pipe spool
SS metal tubing spools
Stainless steel alloy pipe spool fabrication
SS pipe spooling with both end flange
Stainless pipe spool with weld neck flange
Stainless steel alloy flanged pipe spool size chart
| Consturction | Seamless Fabricated | Welded Fabricated | Seamless Fabricated | Welded Fabricated | Welded Fabricated | |
|---|---|---|---|---|---|---|
| Size Range | 0.5″ to 30″ | 0.5″ to 48″ | 0.5″ to 24″ | 0.5″ to 74″ | 0.5″ to 96″ | |
| Schedule / Thickness | Min Thk (mm) | 10s/3 mm | 10s/8 mm | 10s/3 mm | 10s/6 mm | 10s/8 mm |
| Max Thk (mm) | XXS/85 mm | XXS/85 mm | XXS/70 mm | XXS/70 mm | XXS/85 mm | |
Contact us for burr free SS metal pipeline spool with MT on 100% of all fillet welds
SS tubing spools chemical compositions
| Element | S | C | P | Si | Ni | Mn | Cr |
|---|---|---|---|---|---|---|---|
| SS 304 | 0.03 max | 0.08 | 0.045 max | 1.0 max | 8.0 – 11.0 | 2.0 max | 18.0 – 20.0 |
| SS 304L | 0.03 max | 0.35 | 0.045 max | 1.0 max | 8.0 – 13.0 | 2.0 max | 18.0 – 20.0 |
Stainless steel pipe spools mechanical properties
| Element | Density | Tensile Strength | Melting Point | Elongation | Yield Strength (0.2%Offset) |
|---|---|---|---|---|---|
| SS 304 | 8.0 g/cm3 | Psi – 75000 , MPa – 515 | 1400 °C (2550 °F) | 35 % | Psi – 30000 , MPa – 205 |
| SS 304L | 8.0 g/cm3 | Psi – 75000 , MPa – 515 | 1400 °C (2550 °F) | 35 % | Psi – 30000 , MPa – 205 |
SS pipe spool fabrication parts
- Reducer – Concentric reducer, eccentric reducer
- Flanges – Blind, weld neck, slip-on, etc.
- Pipes – Seamless/Welded
- Elbow – 90° / 45° / 180°
- Tee – Equal Tee, Unequal Tee
Stainless steel pipe spools advantages
- The capacity to use specialized coatings
- Field installation simplicity
- Monitoring and confirming the position of the fitting and the quality of the weld
- Pre-Drilling and fitting preparation without full operational conditions
- Testing for pressure and welding in a secure workshop setting